Become a member

Printed joints, explained.

Every joint here has a teaching sheet: why it works, the numbers to start your own design from, where to use it, and a 3MF file so you can print it and try it. We’re opening the library in stages.

10 open now. 26 more on the way.

26 more joints are coming soon.

New to 3D printing? Start with The First Layer, our beginner class in Singapore.

Dowel joint

Pins and snap fits

Two halves, three dowels

Dowel jointloose pin, dowel pin

A 40 mm capsule that opens in two. Three short printed dowels line the halves up and hold them shut, and a small flat underneath stops it rolling.

FDM, PLA, 0.4 mm nozzle

Why it works

  1. The dowels cross the seam and take every sideways push, so the halves can’t slide or twist apart. The holes only have to grip.
  2. Each hole is c = 0.15 mm bigger than its dowel: tight enough to hold, loose enough to pull apart by hand. Holes printed straight up come out round, so all three line up.
  3. Three dowels at 120° look the same when a half is flipped, so both halves share one design. Only the bottom one gets the flat.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side. d is the dowel diameter.

Dowel, printed lying down
Ø 3 × 10 mm
Hole, 5.5 mm deep
d + c = Ø 3.15 mm
Boss round each hole
1.3 mm wall
Seam chamfer and notch
0.4 mm, V 1.4 mm deep
Flat underneath
Ø 12.5 mm, 1 mm off
Ball / inside
Ø 40 / Ø 34 × 31 mm
Thinnest wall
2.3 mm
Dowel circle
Ø 32 mm, 3 × 120°

Print both halves seam face down: the 45° roof inside needs no support. Lay the dowels on their 0.3 mm flat, which lets air out of the blind holes. Too tight? The file has three 2.90 mm spares to swap in before you reprint anything else. Steel 3 × 10 mm pins fit the same holes.

Apply it when

  • Capsules and keepsakesSmall boxes that open in two.
  • Split modelsBig prints made in parts.
  • Furniture-style joineryPrints that join like woodwork.

In the print file

8 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Dowel joint3MF print file, 754 KB
Download
Alignment pins

Pins and snap fits

Halves that line up

Alignment pinsprinted pegs, registration pins

The 40 mm capsule again, with the pins built in: three pegs on the bottom half push into the top, spaced so it fits one way only.

FDM, PLA, 0.4 mm nozzle

Why it works

  1. The pegs line the halves up exactly, so the seam closes flush. Each hole is c = 0.15 mm bigger than its peg, so the halves grip and still pull apart by hand.
  2. The pegs sit 110°, 125° and 125° apart, so the top fits one way only: never rotated, never flipped. The thumbnail notches always meet.
  3. Fewer parts than loose dowels, but the pegs print upright and are weakest across the layers. So they’re fatter, 3.5 mm, with a 0.4 mm fillet at the root.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Peg, printed upright
Ø 3.5 × 5 mm
Hole, 5.5 mm deep
peg + c = Ø 3.65 mm
Boss under each peg
45° end
Seam chamfer and notch
0.4 mm, V 1.4 mm deep
Flat underneath
Ø 12.5 mm, 1 mm off
Peg spacing
110°, 125°, 125°
Root fillet
0.4 mm
Ball / inside
Ø 40 / Ø 34 × 31 mm

Print A seam face down with no support. B prints on its flat with the pegs up and needs support under the lower dome only; tree supports peel off the outside. Too tight? Sand the pegs lightly, or print A again with 3.75 mm holes. For big split models, your slicer’s cut tool can add pins and holes for you.

Apply it when

  • Capsules and clamshellsTwo halves that must meet perfectly.
  • Models too big for the bedCosplay helmets, statues and signs.
  • Multi-colour partsPrint each colour alone, then pin them together.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Alignment pins3MF print file, 751 KB
Download
Annular snap fit

Pins and snap fits

A cap that snaps on

Annular snap fitsnap-on cap, ring snap

A small bead inside the cap clicks into a groove round the tube, like the cap on a marker pen.

FDM, PLA or PETG, 0.4 mm nozzle

Why it works

  1. To get past, the bead has to stretch the whole ring of the skirt, which is far stiffer than bending one clip. So keep the bead small.
  2. Slots split the skirt into fingers that bend like clips, so a stiff ring snaps on easily.
  3. A groove in the tube, not a bump, keeps the outside smooth and lets the cap sit flush.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Bead height y
y = ε × d, about 1.2% of d
Skirt lead-in chamfer
0.5 mm, 30°
Side gap
c = g ÷ 2
Relief slots
4 to 6 round the skirt
Skirt wall
1.2 mm
Groove
bead shape + 0.1 mm

ε is the safe strain (1.2% for PLA) and d is the tube diameter. On a 30 mm tube that’s a bead of about 0.36 mm, which is what the print file uses. Any bigger and a skirt without slots stretches past what PLA can safely take, so add relief slots, print in PETG, or both.

Apply it when

  • Caps on tubesPen caps, pipe end caps and bottle tops.
  • Round housingsKnobs on shafts and lens caps.
  • Light sealingA continuous ring that keeps dust out.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Annular snap fit3MF print file, 38 KB
Download
Twist-lock (bayonet) mount

Slides, twists and moving joints

Push, then twist

Twist-lock (bayonet) mountbayonet mount, push and twist

Lugs inside the cap drop into L-shaped slots round the tube. A short twist locks it, like a camera lens.

FDM, PLA or PETG, 0.4 mm nozzle

At a glance

  • 3 lugs, 120° apartThey centre the cap and share the load.
  • A 30 to 60° twistNo threads to cross.
  • Slots slope 1 to 2°Twisting pulls the cap tight.

Why it works

  1. Each lug drops straight down its entry slot, then twists along the side slot round the ring. The cap locks with no threads at all.
  2. A small bump near the end of each slot clicks the lug into place, so it won’t twist loose by itself.
  3. Three lugs spaced evenly round the ring centre the cap and share the load between them.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Slot width
lug + g
Detent bump
0.3 to 0.5 mm
Entry chamfer
0.5 to 1 mm
Lugs
3, 120° apart
Lug size, w × t
3 × 3 mm or more
Slot depth into the tube
lug + g
Holding force
F = n × τ × w × t

Slope each side slot down by 1 to 2° toward its end, so twisting draws the cap tight against its seat, the way a camera lens mount does. Print the tube and cap with their rings flat on the bed so they stay round, and give the lugs a 45° underside so they print without supports. F is the straight pull that shears the lugs off, an upper limit: n is the number of lugs, τ the plastic’s shear strength, w the lug width round the ring and t the lug height along the axis.

Apply it when

  • Quick-open containersJars and capsules opened with a short twist.
  • Swappable attachmentsNozzles, lens hoods and tool heads.
  • Mounts that mustn’t shake looseThe detent bump holds it locked.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Twist-lock (bayonet) mount3MF print file, 46 KB
Download
Threaded lid

Screws, nuts and fixings

A lid that screws on

Threaded lidscrew cap, printed thread

Tinkercad can draw the thread for you. The trick is giving the lid’s copy enough room to turn.

FDM, PLA, 0.4 mm nozzle

In Tinkercad

  1. Thread the neck. Put a thread shape on the jar’s neck.
  2. Copy it. Duplicate the thread and set the copy to Hole.
  3. Widen the copy. Make it 2c wider in X and Y.
  4. Group. Group the hole into the lid.

Why it works

  1. The lid’s thread is a copy of the jar’s, turned into a hole and widened a little, so the two always match.
  2. Coarse, chunky threads print well. Fine bolt-style threads blur together at 0.2 mm layers.
  3. Print both with the thread axis pointing up. The 45° flanks then print without supports.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Pitch P
2 to 3 mm
Lid copy
+ 2c in X and Y
Thread starts below the rim
1 to 2 mm
Lid lead-in chamfer
1 mm
Wall behind the thread
1.6 mm or more
Turns of thread
1.5 to 3
Thread depth
0.541 × P

Tinkercad’s thread shapes and their settings move around between updates, so search the Shapes panel for “thread”. Whatever it’s called, widen the hole copy in width and depth only, never height: stretching the height changes the pitch, and the lid jams after half a turn. The print file uses a 2.5 mm pitch.

Apply it when

  • Sealed containersJars, capsules and geocache tubes.
  • Screw-together tubesLengths joined end to end.
  • Covers opened many timesThreads don’t wear like clips.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Threaded lid3MF print file, 1134 KB
Download
Dovetail slide

Slides, twists and moving joints

A slide that can’t lift

Dovetail slidesliding dovetail joint

A tongue that’s wider at its base than at its neck slides along a matching groove, and the two parts can’t pull apart.

FDM, PLA, 0.4 mm nozzle

Why it works

  1. The tongue is wider at its base than at its neck, so once it’s in the groove the parts can only slide, never lift apart.
  2. The gap on the sloped flanks sets how freely it slides. The flat faces get a bigger gap so they never rub.
  3. 45° flanks (θ = 45°) print cleanly on both parts with no supports and still lock them together.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Flank angle θ
45°
Offset on each flank
Δx = c ÷ sin θ
Gap at the groove floor
0.4 mm
Gap between flat faces
0.3 to 0.5 mm
Tongue height
3 to 5 mm
End chamfers
0.5 mm, both parts

Want it to lock as it goes in? Taper the groove 0.2 mm narrower over its length. It slides freely at first, then wedges snug at the end. Print both parts with the slide running flat along the bed.

Apply it when

  • Rail mountsLights, cameras and accessories that slide on.
  • Modular systemsParts that slide together and swap out.
  • Drawers and traysSlides that can’t lift off their track.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Dovetail slide3MF print file, 2 KB
Download
Sliding lid

Slides, twists and moving joints

A lid on rails

Sliding lidpencil-box lid with a stop tooth and two detents

The lid’s edges ride in grooves inside the box walls, like a pencil box. A bump on the end wall clicks into a dimple when the lid is fully closed and fully open, and a small tooth stops it sliding all the way out.

FDM, PLA or PETG, 0.4 mm nozzle

How it moves

  1. Push in once. The ramp rides over the low end wall and the lid flexes a little.
  2. Closed. The bump on the end wall sits in the front dimple, so the lid stays shut.
  3. Pull open. The tooth hits the wall and the bump clicks into the back dimple.

Why it works

  1. The lid’s edges sit in grooves cut into the inside of the walls, below their tops, so it can only slide, never lift.
  2. A small bump on the low end wall rides under the lid. Between the stops the lid flexes up over it. At fully closed and fully open the bump drops into a dimple and clicks, so the lid stays put.
  3. A tooth under the lid’s back end hits the low end wall as you pull, so the lid stops instead of falling out. Its front is a ramp, so it clicks in over the wall once when you put it together.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Stop bump (tooth)
0.5 mm
Ramp on the front face
30 to 45°
Gap over the low end wall
c, 0.15 mm
Groove depth, 45° roof
1.5 to 2 mm
Detent bump on the end wall
Ø 2.4, 0.55 tall
Dimples, closed and open
Ø 2.8, 0.5 deep
Lid edge
groove − g
Lid thickness
2 mm

The bump stands 0.4 mm above the lid’s underside, so the lid only has to flex a little to pass it: firm clicks, no wear. Want it to click harder? Add 0.1 mm to the bump, not to the dimples. Print the box upright and the lid flat with the tooth and dimples facing up, so neither needs supports.

Apply it when

  • Pencil and card boxesThe classic slide-top box.
  • Battery compartmentsA cover that slides off sideways.
  • Lids that mustn’t get lostThe stop tooth keeps the lid attached.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Sliding lid3MF print file, 21 KB
Download
Bead snap fit

Fit basics

A lid that snaps shut

Bead snap fitsnap-on lid, undercut lid

A small bead on the box rim pushes the lid’s skirt outward. The skirt springs back and hooks under it with a click.

FDM, PLA, 0.4 mm nozzle

Why it works

  1. The gentle front slope (the lead-in) turns your downward push into a sideways bend of the skirt.
  2. The back face of the bead decides how hard the lid is to open. Steep holds for good; sloped lets go.
  3. The skirt is a clip bent into a ring, so the same rules as a cantilever clip apply. Cut slots if it’s too stiff to flex.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Lead-in angle
about 30°
Bead height y
0.3 to 0.5 mm
Side gap
c = g ÷ 2
Skirt wall
1.2 to 1.6 mm
Back face
45° opens, 90° locks
Relief slots
every 20 to 30 mm
Skirt flex
y = 0.67 × ε × L² ÷ t

Corners of a square lid barely flex, so run the bead along the straight sides and stop it short of the corners. A round lid flexes evenly; 4 to 6 slots usually do. In the flex formula, ε is the safe strain (1.2% for PLA), L is the skirt length from the lid’s top down to the bead and t is the skirt wall.

Apply it when

  • Containers that get knocked overFood, craft and parts boxes whose lids must stay on.
  • Lids opened every dayPill boxes, sample jars and storage tubs.
  • Keeping dust outA continuous bead seals better than a few clips.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Bead snap fit3MF print file, 6 KB
Download
Detent

Fit basics

A bump that finds its dimple

Detentbump and dimple, nub fit

A small rounded bump on one part drops into a matching hollow on the other. It holds the parts in place with a soft click.

FDM, PLA or PETG, 0.4 mm nozzle

Give the bump something to flex

  • Thin wallThin the part behind the bump.
  • Slots either sideCut a free tongue around it.
  • On a clip armLet the clip’s spring do the work.

Why it works

  1. The bump drops into the dimple and stays there until you push hard enough to lift it out.
  2. To lift out, something has to flex by the bump’s height. Put the bump on a thin wall or a free tongue.
  3. Round bumps in round dimples click smoothly. Sharp edges grind and wear flat.

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Bump height
0.3 to 0.5 mm
Dimple width
bump Ø + g
Flexing wall
1.35 mm (3 perimeters)
Bump size
round, Ø 2 to 4 mm
Dimple depth
= bump height
Print the bump
facing up

A dimple a little shallower than the bump holds harder, because the wall never fully relaxes. Match them for a soft click. Several dimples in a row turn this into a slider or dial with set steps.

Apply it when

  • Holding a position lightlyA drawer or lid that stays shut until you pull it.
  • Click feedbackA dial or slider that clicks at each step.
  • Stopping rattlesA bump that takes up the slack in a loose fit.

In the print file

2 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Detent3MF print file, 42 KB
Download
Friction fit

Fit basics

A box lid that grips

Friction fitpush fit, snug lid

The lid’s lip presses inside the box wall with almost no gap, so friction holds it on. Everything depends on how small that gap is.

FDM, PLA, 0.4 mm nozzle

Why it works

  1. Printed plastic spreads a little wider than drawn, so you still leave a gap. For a friction fit it’s about half the gap of a sliding fit.
  2. The gap is per side: c on each side, so the lip = inside − 2c. With c = g ÷ 4, about 0.08 mm, the walls just touch once printed and friction holds the lid.
  3. A small chamfer on the lip guides it in, even when the first layers bulge out (elephant’s foot).

Starting numbers

g is your gap from the peg-and-hole test (start at 0.3 mm), so hole = peg + g. c = g ÷ 2 is the share on each side.

Lip height
5 to 8 mm
Gap per side, friction
c = g ÷ 4
Lid too loose, or too tight
c = 0, or c = g ÷ 2
Lip chamfer
0.5 mm × 45°
Box wall
1.6 to 2.0 mm
Lip wall
1.35 mm (3 perimeters)
Lip outside size
inside − 2c

Design from the box’s inside size, not its outside. Print the lid upside down so the lip comes out crisp. A taller lip grips harder than a tighter one. Friction fits loosen with wear: if the lid gets easy, reprint it with c = 0.

Apply it when

  • Storage boxes and casesA parts box, pill box or desk organiser with a lift-off lid.
  • Covers you open oftenElectronics enclosures and battery covers you open to service.
  • One part sleeves over anotherA cap over a tube, a sleeve over a handle, a cover over a sensor.

In the print file

3 parts, printed in two colours. No screws, magnets or other hardware. Every printer is a little different, so treat the numbers as a first guess and adjust from your own test print.

Open the full teaching sheet

Friction fit3MF print file, 11 KB
Download